安裝氣缸墊圈時，要注意電機的旋轉方向，應保持順時針方向；它也應該接地。油缸清洗機正常啟動后，空機將運行幾分鐘，然后正常工作。冬季使用時，必須預熱12-24小時，然后加水調試。
When installing the cylinder gasket, first pay attention to the rotation direction of the motor, and keep it clockwise; It should also be grounded. After the oil cylinder washer is started normally, the empty machine will run for several minutes and then work normally. When using in winter, it must be preheated for 12-24 hours, and then added with water for debugging.
在使用滾筒清洗機時，要記住行點測試，然后空轉運行2-3分鐘，檢查傳動系統和輸送帶的運動情況，保持平穩狀態，確認一切正常，方可生產。不僅如此，還要時刻注意氣缸清洗機的運行狀態。
When using the roller washer, remember to conduct spot test first, and then run it for 2-3 minutes at idle, check the movement of the transmission system and conveyor belt, keep it stable, and confirm that everything is normal before production. Not only that, but also pay attention to the running state of the cylinder cleaner at all times.
工作結束后，清潔后的氣瓶不能停放在運輸車上，按下停止按鈕停止整機。此外，清洗機中的清洗液應定期加水和一定比例的污垢清洗劑補充消耗，使液位保持在一定高度。
After the work is completed, the cleaned gas cylinder cannot be parked on the transport vehicle. Press the stop button to stop the whole machine. In addition, the cleaning liquid in the cleaning machine should be regularly added with water and a certain proportion of dirt cleaning agent to supplement consumption, so as to keep the liquid level at a certain height.

在全封閉系統中，使用溶劑清洗金屬，因為零件清洗機采用的是獨立式蒸餾系統，確保所有清洗過程中在蒸汽蒸餾后溶劑保持霧狀狀態，且溶劑的清潔度不會改變，有效成分在清洗方面的質量要求。因為作為直接用水清洗的基礎，是無法保證水經過蒸餾后的清潔度的，所以零件清洗機必須使用過濾裝置和大量的水才能有效地實現清洗效率，零件表面需要配合其他設備進行清洗機工作。優良的品質有效提高 效率和節能的優點是零件，降低沸點是清洗槽設計進入真空環境的主要方式，因此在蒸餾零件時，余熱可以有效保證氣化過程，明顯會提高工作效率，零件清洗機每小時清洗周期達到十次以上。
In the totally enclosed system, the solvent is used to clean the metal, because the parts cleaning machine adopts an independent distillation system to ensure that the solvent remains in a mist state after steam distillation in all cleaning processes, and the cleanliness of the solvent will not change, and the quality requirements of effective ingredients in cleaning. As the basis of direct water cleaning, the cleanliness of distilled water cannot be guaranteed, so the parts cleaning machine must use a filter device and a large amount of water to effectively achieve cleaning efficiency, and the parts surface needs to cooperate with other equipment for cleaning. The advantages of good quality, effective efficiency and energy saving are parts. Reducing the boiling point is the main way for the design of the cleaning tank to enter the vacuum environment. Therefore, when distilling parts, the waste heat can effectively ensure the gasification process, which will obviously improve the working efficiency. The cleaning cycle of the part cleaner can reach more than ten times per hour.
清洗機和零件時需要使用一些零件清洗溶劑，溶劑的缺陷是會對空氣造成污染，但我們將零件清洗機設計為全封閉系統，對空氣污染所帶來的獲得明顯的控制，同時由于水基在工作過程中需要依靠表面活性劑的技術途徑，而且活性化學品不能有效分解水資源造成的污染，因此水資源中會有大量的化學殘留物，造成嚴重的污染。經相關部門計算，零件清洗機整體清洗后，可能對環境造成的污染或相對較大，水污染小于溶劑量的2000倍。而部分清洗技術在環境污染后，由于蒸餾技術的結合，所以造成的污染基本上會被完全切斷在蒸餾箱中，所以不必再考慮以后的處理方案，而溶劑工業已經提供了特殊的輸送系統，采用了封閉、安全的溶劑輸送方式，確保零件清洗機的清洗工藝不受影響。
Some part cleaning solvents need to be used to clean the machine and parts. The defect of the solvent is that it will pollute the air. However, we have designed the part cleaning machine as a fully closed system, which can obviously control the air pollution. At the same time, as the water-based needs to rely on the technical approach of surfactant in the work process, and the active chemicals cannot effectively decompose the pollution caused by water resources, Therefore, there will be a lot of chemical residues in water resources, causing serious pollution. According to the calculation of relevant departments, after the overall cleaning of the parts washer, the pollution to the environment may be relatively large, and the water pollution is less than 2000 times of the solvent amount. After environmental pollution, due to the combination of distillation technology, the pollution caused by some cleaning technologies will basically be completely cut off in the distillation box, so it is unnecessary to consider the future treatment scheme. The solvent industry has provided a special transportation system, which adopts a closed and safe solvent transportation mode to ensure that the cleaning process of the part cleaner is not affected.
以上的精彩內容來自：噴淋清洗機濟南科爾超聲波設備有限公司專注通風管道多年，質量保證,服務完善,歡迎更多客戶點擊：http://www.czxhwj.com
The above highlights come from: Jinan Keer Ultrasonic Equipment Co., Ltd. has been focusing on ventilation ducts for many years, with quality assurance and perfect service. Welcome more customers to click: http://www.czxhwj.com